Hot rod shops

Hot rod shop management software for shops with five cars in the air.

A hot rod shop is never working on one car. There is an LS swap waiting on a transmission, a ’32 on the frame table, a ’55 in paint, and a customer on the phone who wants to know about all three. Repair software was not built for that. This was.

14 days free · No credit card · Works with your Shop Toolbox account

Why repair software fights a hot rod shop.

General shop systems are built around a ticket that opens Monday and closes Friday. A speed shop breaks that on every car.

  • There is no book time for an LS swap into a ’55

    Labor guides cover a water pump on a Camry. They do not cover mounts, wiring and a custom driveshaft on a car nobody has done this way before. The hours have to come from your own clock, not a guide.

  • Parts come from everywhere, on everyone’s schedule

    A crate engine from one supplier, a Tremec from another, a set of headers from a swap meet. A stalled car is almost always one part, and a parts screen that only knows “ordered” cannot tell you which one.

  • Your customers are enthusiasts

    They know the difference between a TKX and a T56 and they want to see it go in. A one-line invoice that says “labor — 40 hrs” is how a good customer turns into a difficult one.

What changes when the shop runs on it.

Three screens from a real shop with several builds moving at once.

Parts Manager

Every part on every car, on one screen.

Parts arrive for the car that is not in front of you. The Parts Manager lists the whole shop’s parts grouped by build, each with its own status and receive-by date — so Monday starts with “the shop is waiting on two things”, not a walk round the bays.

  • Needed, ordered, shipped, backordered, installed, invoiced
  • A receive-by date on every part, so late shows as late
  • Photograph the supplier PO and the rows fill themselves in for you to check
The Parts Manager showing 17 parts across 3 builds, with a designated parts manager and a tile filter carrying a photo of each car — the Mustang, the C10, the Bronco — plus vendor, status and due-date filters, and the parts grouped under each build.
Clock-in

The tech picks the car, not a form.

Your crew taps the car they are standing next to and says how deep — the whole build, or one package of it. Clocking out asks for a note. At the end of the week you have a record of what forty hours on the ’32 actually bought.

  • Clock in and out from a phone on the floor
  • A tile for shop time that belongs to no car
  • Hours land on the task and roll into the invoice
The clock-in overlay titled “Pick what you’re working on”: a photo card per build — Ellis Fastback with 10 open, Vaughn Bronco with 2, Okafor C10 with 2 — above a separate “Not on a vehicle” tile for cleanup, training and meetings.
Proposals

A quote the customer can read line by line.

Price the swap as packages — mounts and fabrication, wiring, driveline — at hours times your labor rate, with parts at cost plus a markup the customer never sees. Send a link. They read every package on their phone and decide, and the answer comes back onto the proposal.

  • Several proposals per build, so phase two gets its own price
  • Package templates for the swaps you quote every month
  • The approved total becomes the build’s budget
A proposal for Phase 2 of a Mustang build, numbered P1042, marked Awaiting customer and totalling $50,430.40 pre-tax. Each package shows its scope as chips, an hours slider, a labor rate and a line total.

One LS swap, start to finish.

A customer brings in a ’55 Bel Air for an LS3 and a five-speed. You build the proposal from your saved LS-swap package, adjust the hours, and text the link; they approve the driveline package that night and hold the interior for later. The approved packages become tasks on the board — mounts to Fabrication, harness to whoever does wiring. The crate engine shows as shipped, the transmission as backordered with a date, so when the customer asks why the car has not moved you can say exactly why. Each tech clocks onto the car with a note. When the engine is in and running, you invoice that much — installed parts at your markup, tracked hours at your rate — and the payment syncs to QuickBooks Online under a job for that Bel Air. The interior package is still sitting on the proposal for when they are ready.

Questions hot rod shops ask.

Is BuildMonkey good for a hot rod shop with several builds going at once?

That is what it is built for. Every build has its own board, parts, hours and invoices, and the Parts Manager and dashboard show the whole shop at once, so a car that is stuck stands out without anyone opening it.

How do I quote work that has no book time?

In packages priced at hours times your labor rate, with the hours coming from your own experience — and, over time, from the tracked hours on the builds you have already done. Save the swaps you quote often as package templates.

Can the customer see what is happening on their car?

Yes. Every build has a customer portal: publish an update with photos from the floor and the parts that went on, and the owner reads it from a private link on their phone, without an account.

Can I bill a build before it’s finished?

Yes, as many times as you need. Invoice the finished work — installed parts and tracked hours — and take partial payments as the build goes.

Put a real build in it.

Start your free trial

14 days free · No credit card · Already have a Shop Toolbox account? Sign in.